No power out at the well house?
Flexible solar panels that stick right onto well houses, barns, and shops. No racking and no roof holes. Answer 4 questions below to get your estimate.
By submitting, you agree Divine Energy Solar may contact you by phone, text or email about your estimate. Msg & data rates may apply. No spam.
We'll reach out shortly with your price.
A well house with solar on the roof. The panels feed the pump directly, so you don't have to run new line out from the house.
Thin, light and bendable. It sticks to standing seam metal roofs with no racking and no roof holes.
4.9★ from 200+ installs across Texas.
A thin, frameless solar panel made from CIGS solar cells on a stainless steel backing, under a tough plastic (ETFE) top sheet. No glass and no metal frame. Sunflare makes two lines:
SlimFit: A 14" wide strip that lies flat between the seams of a standing seam metal roof. 65 watts per panel. Comes in two lengths: SlimFit (about 71") and SlimFit XT (about 78").
Flex: A full-size panel, about 65" x 39", made for flat TPO and EPDM roofs. 165–195 watts per panel.
SlimFit: About 4.4 lbs per panel, roughly 0.5 lb per square foot (about 1 lb per square foot with covers and wiring). 75% lighter and 95% thinner than a regular glass panel. Any metal roof gauge works.
Flex: About 11 lbs per panel. An installed Flex system is 86% lighter than regular solar, with no racking and no heavy ballast blocks.
No. Both lines come with a butyl adhesive already on the back. We press them onto the roof with a roller. No racking and no roof penetrations.
SlimFit: Wires run up under the ridge cap or through an adhesive-backed conduit, so nothing gets screwed into the roof.
Flex: Wires and electronics sit in a low-profile raceway that also sticks down. No penetrations there either.
SlimFit: Goes on standing seam metal roofs. The flat section between the seams needs to be at least 14.5" wide. If you're placing 2 or more panels in a row vertically, the maximum width is 18" to fit the junction cover.
Flex: Made for flat TPO or EPDM roofs. Its pitch and roof surface requirements only apply to on-grid systems.
We confirm your roof before we quote.
SlimFit: Rated for 113 lbs per square foot of wind uplift. The adhesive is rated for gale-force winds.
Flex: Rated for 110 lbs per square foot of wind uplift.
Both: Rated for 125 lbs per square foot of snow load.
It depends on your pump size and how much water you use.
SlimFit: 65 watts per panel, so it takes more panels to reach the same power.
Flex: 165–195 watts per panel, so it takes fewer panels, but it needs a flat TPO or EPDM roof.
Your estimate sizes the system to your pump, so you'll know before you spend anything.
Not with panels alone on an on-grid system. Those shut off when the grid goes down, for safety. To keep water running during an outage, you need a battery or an off-grid setup.
SlimFit: Compatible with most major inverters, microinverters, optimizers and batteries.
Flex: Works with standard inverters and power optimizers, which sit inside its wire raceway.
Tell us if you want a battery option in your estimate.
Distance changes how the system gets wired, whether you go with SlimFit or Flex. A well close to the house can tie in differently than one 500 ft out. It helps us give you an accurate price.
SlimFit and Flex both have a bypass diode on every cell. If a branch shades part of the panel, only the shaded cells drop out and the rest keep producing. Regular panels have one diode per string of cells, so a little shade can knock out a whole section.
No. Regular glass panels make more power per square foot.
SlimFit: 16% efficient, 65 watts per panel.
Flex: 13–16% efficient, 165–195 watts per panel.
The tradeoff is that both go where regular panels can't: light roofs, small buildings, and roofs you don't want to drill into.
There's no glass to break. On both SlimFit and Flex, the cells sit on flexible stainless steel under a plastic top sheet.
Both: Tested against 1" hail at 52 mph. Rated from -40°F to 185°F.
It depends on how your system is set up. This applies to both SlimFit and Flex.
Off-grid: 2-year workmanship warranty from Sunflare.
On-grid: 25-year workmanship and power production warranty from Sunflare, with at least 90% output through year 10 and 80% through year 25.
Very little.
SlimFit: Sunflare recommends an inspection every 12–24 months.
Flex: Sunflare recommends an inspection every 12 months.
Both: Clean with water, mild soap and a soft sponge. No pressure washers, brushes or harsh cleaners.
It depends on your roof, your pump and whether SlimFit or Flex fits your building. Answer four quick questions above and we'll send you a free instant estimate.